Flexbox was designed as a single dimensional layout, meaning that it deals with laying out items as a row or as a column — but not both at once. There is however the ability to wrap flex items onto new lines, creating new rows if
row and new columns if
column. In this guide I will explain how this works, what it is designed for and what situations really require CSS Grid Layout rather than flexbox.
The initial value of the
flex-wrap property is
nowrap. This means that if you have a set of flex items that are too wide for their container, they will overflow it. If you want to cause them to wrap once they become too wide you must add the
flex-wrap property with a value of
wrap, or use the shorthand
flex-flow with values of
row wrap or
Items will then wrap in the container. In the next example I have ten items all with a
160px and the ability to grow and shrink. Once the first row gets to a point where there is not enough space to place another 160 pixel item, a new flex line is created for the items and so on until all of the items are placed. As the items can grow, they will expand larger than 160 px in order to fill each row completely. If there is only one item on the final line it will stretch to fill the entire line.
We can see the same thing happening with columns. The container will need to have a height in order that the items will start wrapping and creating new columns, and items will stretch taller to fill each column completely.
Wrapping works as you might expect when combined with
flex-direction is set to
row-reverse then the items will start from the end edge of the container and lay themselves out in reverse ordered lines.
Note that the reversing is only happening in the inline, row direction. We start on the right then go onto the second line and again start from the right. We aren’t reversing in both directions, starting from the bottom coming up the container!
As we have seen from the above examples if our items are allowed to grow and shrink, when there are fewer items in the last row or column then those items grow to fill the available space.
There is no method in flexbox to tell items in one row to line up with items in the row above — each flex line acts like a new flex container. It deals with space distribution across the main axis. If there is only one item, and that item is allowed to grow, it will fill the axis just as if you had a single item flex container.
If you want layout in two dimensions then you probably want Grid Layout. We can compare our wrapped row example above with the CSS Grid version of that layout to see the difference. The following live sample uses CSS Grid Layout to create a layout that has as many columns of at least 160 pixels as will fit, distributing the extra space between all columns. However, in this case the items stay in their grid and don’t stretch out when there are fewer of them on the final row.
This is the difference between one and two-dimensional layout. In a one dimensional method like flexbox, we only control the row or column. In two dimensional layout like grid we control both at the same time. If you want the space distribution row by row, use flexbox. If you don’t, use Grid.
Typically flexbox-based grid systems work by taking flexbox back to the familiar world of float-based layouts. If you assign percentage widths to flex items — either as
flex-basis or by adding a width to the item itself leaving the value of
auto — you can get the impression of a two dimensional layout. You can see this working in the example below.
Here I have set
0 to make inflexible flex items and am then controlling flexibility using percentages, just like we used to do in float layouts.
If you need flex items to line up in the cross axis, controlling the width in this way will achieve that. In most cases however, adding widths to flex items in this way demonstrates that you would probably be better served by switching to grid layout for that component.
When wrapping flex items, the need to space them out is likely to arise. At the current time we do not have any implementations of the gap properties from the Box Alignment module for Flexbox. In the future we will be able to use
column-gap for flexbox as we do for CSS Grid. At the current time you will need to use margins to achieve this.
You can see from the live example below that in order to create gaps that do not also create a gap at the edges of the container, we need to use negative margins on the flex container itself. Any border on the flex container is then moved to a second wrapper in order that the negative margin can pull the items up to that wrapper element.
It is this requirement that the gap properties, once implemented, will solve for us. Proper gaps only happen on the inside edges of items.
The flexbox specification details what should happen if a flex item is collapsed by setting
visibility: collapse on an item. See the MDN documentation for the
visibility property. The specification describes the behavior as follows:
“Specifying visibility:collapse on a flex item causes it to become a collapsed flex item, producing an effect similar to visibility:collapse on a table-row or table-column: the collapsed flex item is removed from rendering entirely, but leaves behind a "strut" that keeps the flex line’s cross-size stable. Thus, if a flex container has only one flex line, dynamically collapsing or uncollapsing items may change the flex container’s main size, but is guaranteed to have no effect on its cross size and won’t cause the rest of the page’s layout to "wobble". Flex line wrapping is re-done after collapsing, however, so the cross-size of a flex container with multiple lines might or might not change.” - Collapsed items
In the following live example I have a non-wrapped flex container. The third item has more content than the others yet is set to
visibility: collapse and therefore the flex container is retaining a strut of the height required to display this item. If you remove
visibility: collapse from the CSS or change the value to
visible, you will see the item disappear and the space redistribute between non-collapsed items; the height of the flex container should not change.
Note: Use Firefox for the below two examples as Chrome and Safari treat collapse as hidden.
When dealing with multiple-line flex containers however you need to understand that the wrapping is re-done after collapsing. So the browser needs to re-do the wrapping behavior to account for the new space that the collapsed item has left in the inline direction.
This means that items might end up on a different line to the one they started on. In the case of an item being shown and hidden it could well cause the items to end up in a different row.
I have created this behavior in the next live example. You can see how the stretching changes row based on the location of the collapsed item. If you add more content to the second item, it changes row once it gets long enough. That top row then only becomes as tall as a single line of text.
If this causes a problem for your layout it may require a rethinking of the structure, for example putting each row into a separate flex container in order that they can’t shift rows.
When you set an item to
display: none in order to hide it, the item is removed from the formatting structure of the page. What this means in practice is that counters ignore it, and things like transitions do not run. Using
visibility: hidden keeps the box in the formatting structure which is useful in that it still behaves as if it were part of the layout even though the user can’t see it.